Sos Roofline Systems

Posts Tagged ‘Foam Insulation’

There are four insulation types’ to consider when choosing insulation they are; batt and blanket, rigid board, loose fill and Expanding foam insulation. I will talk about each individually so you will have a better understanding when choosing insulation.

When choosing insulation Batt and blanket should be considered. It’s is made from fiberglass and rock wool. It’s used in walls and ceilings of unfinished buildings. Contractors usually install between studs 16-24″ apart. It’s the cheapest, but without proper installation it will have a minimal effect. After installing you will need to vapor seal, house wrap or caulk.

The second cheapest to consider when choosing insulation is the rigid foam board. It’s made from polystyrene, polyurethane or fiberglass. It’s used in basement walls, high ceilings, flat roofs and perimeters. It’s not flame resistant. So it required covering with fire proof paneling or dry wall. Since bugs nest in this insulation. It’s suggested to use an insecticide treated material for basements.

The third to consider when choosing insulation is loose fill. This insulation is made from fiberglass or cellulose. It is blown into the walls to make a blanket effect. This insulation is used in attics and walls of unfinished buildings. It’s treated to for fire and moisture protection.

The last is Expanding foam insulation. When choosing insulation I would have to say this is my favorite. Like loose fill it too is blown into walls. As it dries it expands to fit every crack. Once dried excess is cut away and a thermal barrier is applied.

When choosing insulation you should think about Batt and blanket. It’s made from fiberglass and rock wool. It’s installed between studs 16-24″ apart. It’s the cheapest, but proper installation is needed. After installing the house needs winterized further.

Expanding Foam insulation has more benefits. It can be used efficiently in hot or cold temperatures. It reduces noise, condensation, and wind washing. It also helps protect against flood and makes building more structural sound. It improves air quality and lowers utilities. It doesn’t shrink or deteriorate with age. It does not require further winterizing. You can apply Expanding Foam Insulation over old material.

Expanding Foam insulation costs between $1.25 -$2.25 to install, but unlike the other, it doesn’t require extra work. It’s environmental friendly because it takes less energy to produce, does not hurt the ozone layer and reduces global warming gases. It improves air quality and reduces noise.

More interesting stuff on foam insulation and similar subjects is available at AtticInsulationGuide.com – click a link and you will be in the right place for all reflective insulation queries and related matters. Click on a link now !

Ready for an attic conversion and new attic insulation? Do you have an old insulation that doesn’t do its job properly, or don’t you have one at all? When beginning with an attic conversion, what better time to fit in a new insulation if the one you have is old and broken in places?

If you do have a badly fitted or old insulation in your attic that you would like to change for a new one that actually keeps heat in, you will have to pull out the whole floor and the walls to be able to remove it properly, so what better time than now? You have to be precautious when pulling out old insulation by making sure your eyes and mouth are covered to not inhale it.

Doing a little research before fitting a new insulation will help you decide what one is best for you, the attic space and the money you can spend on the insulation. The best insulation is always the most expensive as it tends to last a lot longer and keeps out condensation and damp. Keep in mind that the more money you spend on your insulation the longer it will last in your attic.

Remember that there are different types of insulation and you need to know if you will be installing it yourself to buy a simple insulation kit, if you are doing the insulation yourself it is recommended to buy rolls or batts of insulation, but if you want a professional insulation fitted that tends to last a lot longer, the best to buy is foams called loose fills.

Make sure you are fully prepared for the installation of your attic insulation and have the utilities you need to be able to do the job in a simple, economical and safe way, whatever way you choose to install your insulation. If the job is thoroughly thought out, done properly by a professional or yourself, you will have lower heating bills for many years!

AtticInsulationGuide.com covers all your attic insulation needs, with tips and information. Whether you want to install insulation during an attic conversion or just cut your fuel expenses, go to the site to find out more.

Last winter many suffered from cold drafty homes and high heating bills. They winterize, but that didn’t help. What they didn’t know is poor insulated walls and attics allow heat escape. Spray on foam insulation and installing attic insulation will help to reduce heating costs.

Spray on foam insulation is a liquid insulation made from polyurethane or urethane with a foaming agent. It is easy to apply; you spray the foam into the area, wait until it dries then cut away the excess. Next you apply the thermal cup. There is no need to caulk, vapor barrier, or house wrap. Spray on foam insulation does it for you by producing an air tight seal.

This insulation has many uses some of these include: roofing, walls, ceilings, basements and when installing attic insulation. It has also been used in restaurant freezers, walk in coolers and storage facilities. It’s been used for boats and boat docks. Airlines use it to strengthen airplane wings.

It has many uses for instance; installing attic installation, ceilings, floors, walls and roofs. Restaurants use them in their walk-ins’ and freezers. Sailors use them on boats and boat docks. Some have even strengthened plane wings with the spray on foam insulation.

Many contractors prefer to use this foam in tight enclosed places where installing fiberglass would be a chore. Contractors also use it when installing attic insulations, roof, ceilings, walls, floors.

How is spray on foam insulation applied? It is sprayed into the area and left to dry, generally a few min. Once dry the contractor would then cut off the excess and apply a thermal barrier.

The cost is $1.25 to $2.25 a square foot, depends on wall thickness and type of insulation used. Although cost may seem a bit high you should consider other variables; since it produces an air tight seal there is no need to winterize. Second Spray on foam insulation can be applied over top the old material, so you do not need to spend time and money tearing out the old. Thirdly the difference in utility bills will show a dramatic savings. Lastly you will be surprised how much heat you save after installing attic insulation.

Spray on foam insulation is used in homes, restaurants, boats and planes. It’s handy when working in small area, For instance installing attic insulation. It’s simple to apply and you don’t have a big mess afterwards. Most importantly benefits out weigh the cost of spray on foam liquid insulation.