Sos Roofline Article Central

Iscar now offers a family of high-performance slitting tools that combine the convenience and security of Tang-Grip clamping with the added sturdiness of the completely new Sumo Tec insert grades.

The notion, already validated effective in Tang-Grip parting tools, has now been spread to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a special hand tool, and are held firmly in place without having the need without requiring clamps, upper jaws or set screws that can weaken the insert and obstruct chip flow. The pocket composition utilizes cutting forces to retain the insert seated tightly in position, eliminating any risk of insert pull-out. The Tang-Grip clamping system also fosters more accurate slitting cuts plus increased pocket and insert lifespan.

Iscar's Sumo Tec insert grades showcase a distinct post-coating treatment which greatly increases tool life and dependability.

Introduced in late '07, the brand new Sumo Tec treatment flattens the insert's coated surface to dispose of microscopic stress raisers, diminish heat and friction and boost chip flow. The result is enhanced toughness and opposition to chipping and built-up edge, all leading to greater tool life. The golden-colored flank on Sumo Tec inserts facilitates wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, permitting higher feed rates.

Their increased rigidity leads to straighter, better accurate cuts and lower vibration even in large-diameter cutters. The revolutionary Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same selection of inserts as Tang-Grip parting tools. Additional sizes will be added.

Available Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, providing exceptional resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.

IC830, supplying increased toughness for heavier parting and grooving involving interrupted cuts. It is fitting for any stainless steel & high temperature alloys.

IC908, a hard, fine-grain substrate with outstanding chipping resistance, mixed with a completely new Sumo Tec TiAlN PVD coating. It is perfect for nodular or grey cast iron.

IC928 and 928A, PVD TiAlN-coated tough grades suitable for stainless steel, high temperature alloys and other alloy steels. These grades are also recommended for interrupted cuts and heavy operations.

Each Tangslit and Tang-Grip inserts are attainable in J- or C-type chipformer geometries from Iscar.

Iscar Adds Their Latest Innovations To A Lengthy Line Of Prospering Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.

Various Progressions Have Expanded Iscar's Line Of Indexable Endmills For Increased Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.

Completely New Tools And Carbide Insert Arrangements From Iscar To Better Improve The Machining Process
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.

A Few Of The Countless Improvements In Carbide Inserts Coming From Iscar
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.

A Handful Of Upgrades In Carbide Inserts Thanks To Iscar Across The Former Decade
Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance.

Push Pull Testing For Building Industry With Calibrated Measuring Instruments. Stress Load Testing Procedures For On Site Documentation To Testing Standards.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.

Be Aware Of Automotive Manufacturing Jobs.
There is no point in denying that workers serving in the automotive industry are also suffering from the economic recession that everybody is experiencing world wide.

Modern Car Manufacturing Jobs To Assist Saving The Economic State
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.